CPU Fan Speed Error Detected: Press F1 to run setup

Hardware devices such as laptops can develop issues with a CPU fan. And then, during the startup, users can come across an error, bearing the following message – CPU Fan error: Press F1 to run setup. It is an error bulletin that can be resolved by taking advisable action.

CPU Fan Speed Fault Detected

Ensure that the CPU fan is properly installed on the CPU Fan header or adjust/disable the Fan Speed Depression Limit choice in the UEFI/BIOS.

CPU Over Temperature Fault 1

Press F1 to run setup.

CPU Fan error: Press F1 to run setup

Information technology has been seen, the warning is ordinarily triggered when you've turned on your PC. As such, the fan error occurs before Windows 10 Os boots and probably caused due to some hardware issue, and Information technology may not exist due to overheating.

You tin follow these tips to resolve the issue and get your CPU fan up and running:

1. Press F1
2. Place your PC in a cool place.
3. Clean your CPU fans thoroughly.
4. Install a good airflow solution.
5. Keep your PC in a absurd place.
6. Check your CPU fan'due south settings
7. Change BIO settings
8. Go it checked by a Hardware technician.

Find the more detailed description below!

1] Press F1

First, every bit recommended by them, printing F1 to run the setup and follow the on-screen instructions.

The completion of this task should help. But if it does non, then go along to the nest suggestions.

2] Place your PC in a absurd place

Heat is an inevitable byproduct of calculator hardware performance, but too much heat can cause a slowdown beyond your system. Then, the ambient temperature where yous place your reckoner plays a cardinal role in keeping your CPU fan absurd. The idle temperatures nether which your CPU fan can function optimally ranges somewhere between 32 – 40 Celsius degrees.  If the temperature exceeds this range, it can probable warm up your PC. Even direct exposure to sunlight tin raise the temperature. And so, the best manner to avoid the fault events is to place your computer in a cool identify and under some sort of shade or roofing.

iii] Clean your CPU fans thoroughly

For a CPU fan that is covered upwardly with a thick coat of clay and dust, you may employ a cotton swab soaked in isopropyl alcohol. The alcohol removes whatsoever grime that has settled on the fan blades. Y'all can make clean the interior and remove grit with an air gun or canned air. Avoid the use of whatsoever spraying or cleaning agents onto whatsoever parts, equally this may damage some of the components.

Alternatively, you lot can apply external fans or heat dissipation devices to cool your computer. The usually used small USB fans, household stand fans, or air conditioners make an platonic setup that can go on the components of your computer, including the CPU fan sufficiently cool and allows you to get the all-time performance from your arrangement.

Read: Free Laptop Cooling Software for PC.

4] Install a adept airflow solution

You tin meliorate the corporeality of air that flows in, either past optimizing fan placement or by providing airflow options to the architect. PC fans come in varying sizes (from a mutual 120mm case fan to more specialized configurations), depths, noise levels, and aesthetic considerations. You can choose the 1 that optimizes airflow and keeps your PC cool.

Read: How to prevent or prepare Overheating and Noisy Laptop Fan issues.

5] Cheque your CPU fan's settings

If some software-related issue is causing this error, you can confirm it by check the CPU fan'south settings in BIOS. This method is occasionally used to troubleshoot tech issues.

Enter the BIOS system of your PC and go to Advanced Settings. You'll demand to utilise the left and correct arrows to navigate your manner to the Avant-garde Settings.

Switch to Hardware Monitor to access your CPU Fan settings. Here. Configure the status as follow:

• Active Heat Sink – Enabled
• Fan Duct with Fan – Enabled
• Passive Heat Sink – Disabled
• Fan Duct without Fan – Disabled

In one case done, salve your changes and get out BIOS setup.

Read: What to do when your CPU Fan runs at total speed always?

vi] Alter the BIOS setting

If y'all can encounter your CPU fan working properly and you're sure your reckoner isn't overheating or running too hot, follow this solution to bypass the CPU fan error message and get your device upwards and running properly. Annotation – It requires yous to make changes to the BIOS setting. So, please proceed advisedly!

1. Open the BIOS setup of your computer and select Monitor.
2. Motility to Fan Speed Monitor entry, use arrow keys to go to navigate.
3. Hither, set the Fan Speed from N/A (Not Available) to IGNORE.
4. Next, switch to Get out and relieve the changes yous've merely finished making.
5. Following this, restart your reckoner and check if the problem persists.

The CPU Fan error message should no more appear during the Windows boot.

Related: 511-CPU Fan not detected error during Kick.

vii] Get it checked by a Hardware technician

If nothing helps, yous may demand to go the CPU Fan and its connections checked by a Hardware technician

All the best.

Source: https://www.thewindowsclub.com/cpu-fan-error-press-f1-to-run-setup

Posted by: josephboung1960.blogspot.com

Share this post